Powermaster CSWI-2004 1/2HP 230 - 208 1 Phase Volt Commercial Heavy Duty Swing #52

Swing Gate Operators

Model CSWI Swing Gate Operator

The CSWI is designed for use on gates with a maximum weight of 1800 pounds and a maximum width of 30 feet. The gate will travel from open to close in approximately 13 seconds and is rated for a maximum of 45 cycles per hour. The CSWI is available from 1/2 1-2 HP in single for three phase. The drive arm is easily disconnected for manual operation in case of power failure. This unit is UL 325 listed for use in Class 1 through Class IV applications.

Electrical Specifications:

• Solid state control board with diagnostic LED s to indicate all input and output functions.
• External control input terminal connections for:
  
  • Radio Receiver
  • Push Button Control Station
  • Key Switches
  • Loop Detectors
  • Card Key Readers
  • Telephone Entry Systems, Etc.
• Timer to close with 0-60 sec. Adjustment standard. Longer timer available upon request.
• Maximum run timer for equipment protection (self-adjusting).
• Master/Slave option with dedicated terminal connection provided.
• Easy Left/Right changeover.
• Time delay on reverse to insure smooth gate motion and less stress on equipment.
• Spike suppressing circuitry for surge and lightning protection.
• Emergency control enabling circuitry for safety with security.
• Electrical dynamic brake for precise gate positioning.
• Magnetic gate lock control circuitry with 115 Volt output terminals.
• Integral current sensing anti-entrapment circuitry with independent opening and closing sensitivity adjustment.
• External anti-entrapment circuitry with separate terminal connections for easy installation of contact and non-contact sensors.
• 1/2 HP., 115 Volt AC, 6 Amp., 1 Phase, instant reversing, switchless, PSC motor, with thermal overload protection and high speed ball bearings for smooth, quiet operation.
• Internal On/Off power switch.
• Two grounded 115 Volt AC, 15 Amp. Convenience receptacles.
• NEMA 1 three-button control station included.

Mechanical Specifications:

• Heavy duty #7 Ga. Steel frame providing a strong and durable unit.
• Hard shell baked-on weather resistant powder coating with an attractive textured finish for years of aesthetic protection from the elements.
• Timing belt primary reduction for smooth, quiet and positive operation.
• Heavy duty 45:1, oil bath type gear reducer for long service and dependable operation.
• Heavy duty #50 sprocket and roller chain arrangement for final drive reduction.
• Heavy duty pillow block type ball bearings supporting output drive shaft and enabling extended endurance under heavy loads with low maintenance.
• Drive arm easily disconnected for manual operation in case of power failure.
• Easily adjustable limit switch cams for precision gate positioning.
• Soft start and stop at the open and close limits of travel, due to the inherent geometry of the articulating drive arm linkage.
• Pad mounted for a strong, solid installation.

Technical Specifications:

• Power requirements: 230/208 Volts, 1 phase
• Class 2 low voltage control circuit.
• Available horse power: 1/2 HP.
• Maximum gate weight: 1800 LBS.
• Maximum cycles per hour: 45 CPH.
• Maximum gate width: 30 feet.
• Gate speed: 13 seconds from open to close.
• UL 325 Listed for use in Class I through IV application.
• Shipping weight: approx. 220 LBS.

Optional Equipment:

• Radio Control.
• Safety Edge (contact safety sensor).
• Photo Cell (non-contact safety sensor).
• Loop Detector.
• Card Key Reader.
• Magnetic Gate Lock.
• Gear Box Heater (for cold climates).
• Thermostatically Controlled Cooling Fan (for hot climates).
• Interior and Exterior Control Stations:
  
  • Push Buttons
  • Push Button with Keyed Lockout
  • Key Switches
• Padlockable Option to secure cover for increased tamper proof protection.
• Three Second Advance Audio Warning Signal available upon request.
• Slow Speed Option (18 sec. From open to close).
• Super Slow Speed Option (23 sec. From open to close).